S124M4 Ribbon Fiber Fusion Splicer
S124M4 Ribbon Fiber Fusion Splicer
| Specifications | |||
|---|---|---|---|
| Applicable Fibers *¹ | SM (ITU-T G.652 / G.657A1 / G.657A2) MM (ITU-T G.651) DS (ITU-T G.653) NZD (ITU-T G.655) BIF (ITU-T G.657.A1/A2) |
||
| Fiber Count | Up to 4-fibers | ||
| Cladding Diameter | 125µm | ||
| Fiber Coating Diameter | Single Fiber: 0.25mm, 0.9mm Ribbon Fiber: Refer To Fiber Holder |
||
| Fiber Cleaving Length | 10mm | ||
| Average Splice Loss *² | SM: 0.05dB MM: 0.03dB DS: 0.08dB NZD: 0.08dB BIF: 0.05dB |
||
| Typical Splice Time | 4-fiber ribbon: 13sec. Single fiber: 13sec. |
||
| Typical Heating Time | 4-fiber ribbon: 14sec. (S924, power mode) Single fiber: 13sec (S921, power mode) |
||
| Splice Program | Max. 300 | ||
| Heat Program | Max. 100 | ||
| Applicable Protection Sleeve Length | 40mm / 60mm | ||
| Tension Test | 1.96N | ||
| Discharge Compensation Function | Automatic correction according to temperature and atmospheric pressure | ||
| Optical Fiber Viewing Method | Two-way observation from X and Y axes | ||
| Monitor | 4.3 inch wide LCD monitor with touch screen | ||
| Magnification | 56X | ||
| Splice Result Storage / Image Capture Capacity |
Last 10,000 splices / Last 100 images to be automatically captured |
||
| Dimensions | 139W x 209D x 114H mm not including shock absorber 179W X 246D X 131H mm including shock absorber |
||
| Weight | 1.8kg (with battery) | ||
| Data Output | USB ver.2 mini B X 1 port, Standard A X 1 port | ||
| Power Source | AC: 100-240V (50/60Hz) DC 11-24V | ||
| Battery Capacity *³ | 170 splice and heating cycles | ||
| Operating Condition | Altitude : 0-2,000m Wind protection : 15m/s Operating temperature : -10 to +50 °C (non-condensing) |
||
| Storage Condition | -40 to +60 °C (non-condensing) | ||
| Note | *1 Corresponding to optical fiber in compliance with ITU-T recommendation. *2 This numerical number is the one when measured for the purpose to show the fusion splice characteristics in the testing method of IEC 61073-1, it is not the one to guarantee the splicing loss. *3 Number of times that the fusion splicing of the fiber and the heat reinforcement can be performed continuously at a rate of once a 90seconds at the room temperature (20°C)an be condition when using a new 100% charged battery. The number of times you can use depends on the state of the battery and usage. |
||
| Environmental Durability | |
|---|---|
| Drop Impact | Vertical drop test (5sides excluding the top side) is conducted from a height of 76cm and the normal operation is confirmed. |
| Impact Protection | The normal operation is confirmed after dropping a 500grams weight of IK 07 grade from the height of 40cm onto the equipment. |
| Dustproof | The normal operation is confirmed after putting the equipment in a device containing dust of 25μm or less for 8hours. |
| Drip Proof | The normal operation is confirmed after exposing water droplet of IPX 2 grade with 3mm/min to 4sides for 2.5min or more tilted by 15degree. |
| Note | * It is not the guarantee of no break or no failure of this product since the test is performed with the draft shield closed. |
| Standard Package | |||
|---|---|---|---|
| Item | Model No. | S124M4-3-0 (Q'ty) |
S124M4-3-1 (Q'ty) |
| S124M4 main body | S124M4-X-A-0001 | 1 | 1 |
| Hard carrying case | HCC-11 | 1 | 1 |
| Battery pack | S947 | 1 | 1 |
| Spare electrode | ELR-01 | 1 pair | 1 pair |
| AC adapter | S979 | 1 | 1 |
| AC power cord | – | 1 | 1 |
| Cooling tray | CTX-03 | 1 | 1 |
| Fiber reformer (4 fiber) | FRF-01 | 1 pair | 1 pair |
| Cleaning brush | VGC-01 | 1 | 1 |
| Electrode sharpener | D5111 | 1 | 1 |
| Tool case | TCC-01 | 1 | 1 |
| LCD antireflectifve sheet | ARS-01 | 1 | 1 |
| Rubber foot | RBC-01 | 1 pair | 1 pair |
| Quick Reference guide | FTS-B559 | 1 | 1 |
| Instruction manual | UMC-03 | 1 | 1 |
| Wi-Fi dongle | WFD-01 | 0 | 1 |
| Optional components | |
|---|---|
| Item | Model No. |
| Soft carrying case | SCC-01 |
| Battery Charger | S980 |
| Angled Stand | AGS-02 |
| Strap plate | SPL-01 |
| Work belt | WBT-01 |
| USB cable | USB-01 |
| Car cigarettes cable | CDC-04 |
| Fiber holder | |
|---|---|
| Item | Model No. |
| Fiber Holder (0.25mm Coating Fiber) | S712S-250 |
| Fiber Holder (0.90mm Coating Fiber) | S712S-900 |
| Fiber Holder (2 Fiber Ribbon) | S712A-002 |
| Fiber Holder (4 Fiber Ribbon) | S712A-004 |
| Fiber Guide V-groove | |
|---|---|
| Fiber count, pitch | Model No. |
| 0.25mm pitch, 4 fiber | FGV-04-P250 |
| Protection Sleeve | ||
|---|---|---|
| Model No. | Applicable Fiber | Length |
| S921 | Single fiber, 0.25 – 0.9mm coating dia. | 60mm |
| S922 | Single fiber, 0.25 – 0.9mm coating dia. | 40mm |
| S924 | Single fiber and up to 8-fiber ribbon | 40mm |
For additional information please contact your sales representative. You can also visit our website at www.lightera.com or call 1-888-FIBERHELP (1-888-342-3743) USA or 1-770-798-5555 outside the USA. For a full list of our certifications, visit our website.
| Specifications | |||
|---|---|---|---|
| Applicable Fibers *¹ | SM (ITU-T G.652 / G.657A1 / G.657A2) MM (ITU-T G.651) DS (ITU-T G.653) NZD (ITU-T G.655) BIF (ITU-T G.657.A1/A2) |
||
| Fiber Count | Up to 4-fibers | ||
| Cladding Diameter | 125µm | ||
| Fiber Coating Diameter | Single Fiber: 0.25mm, 0.9mm Ribbon Fiber: Refer To Fiber Holder |
||
| Fiber Cleaving Length | 10mm | ||
| Average Splice Loss *² | SM: 0.05dB MM: 0.03dB DS: 0.08dB NZD: 0.08dB BIF: 0.05dB |
||
| Typical Splice Time | 4-fiber ribbon: 13sec. Single fiber: 13sec. |
||
| Typical Heating Time | 4-fiber ribbon: 14sec. (S924, power mode) Single fiber: 13sec (S921, power mode) |
||
| Splice Program | Max. 300 | ||
| Heat Program | Max. 100 | ||
| Applicable Protection Sleeve Length | 40mm / 60mm | ||
| Tension Test | 1.96N | ||
| Discharge Compensation Function | Automatic correction according to temperature and atmospheric pressure | ||
| Optical Fiber Viewing Method | Two-way observation from X and Y axes | ||
| Monitor | 4.3 inch wide LCD monitor with touch screen | ||
| Magnification | 56X | ||
| Splice Result Storage / Image Capture Capacity |
Last 10,000 splices / Last 100 images to be automatically captured |
||
| Dimensions | 139W x 209D x 114H mm not including shock absorber 179W X 246D X 131H mm including shock absorber |
||
| Weight | 1.8kg (with battery) | ||
| Data Output | USB ver.2 mini B X 1 port, Standard A X 1 port | ||
| Power Source | AC: 100-240V (50/60Hz) DC 11-24V | ||
| Battery Capacity *³ | 170 splice and heating cycles | ||
| Operating Condition | Altitude : 0-2,000m Wind protection : 15m/s Operating temperature : -10 to +50 °C (non-condensing) |
||
| Storage Condition | -40 to +60 °C (non-condensing) | ||
| Note | *1 Corresponding to optical fiber in compliance with ITU-T recommendation. *2 This numerical number is the one when measured for the purpose to show the fusion splice characteristics in the testing method of IEC 61073-1, it is not the one to guarantee the splicing loss. *3 Number of times that the fusion splicing of the fiber and the heat reinforcement can be performed continuously at a rate of once a 90seconds at the room temperature (20°C)an be condition when using a new 100% charged battery. The number of times you can use depends on the state of the battery and usage. |
||
| Environmental Durability | |
|---|---|
| Drop Impact | Vertical drop test (5sides excluding the top side) is conducted from a height of 76cm and the normal operation is confirmed. |
| Impact Protection | The normal operation is confirmed after dropping a 500grams weight of IK 07 grade from the height of 40cm onto the equipment. |
| Dustproof | The normal operation is confirmed after putting the equipment in a device containing dust of 25μm or less for 8hours. |
| Drip Proof | The normal operation is confirmed after exposing water droplet of IPX 2 grade with 3mm/min to 4sides for 2.5min or more tilted by 15degree. |
| Note | * It is not the guarantee of no break or no failure of this product since the test is performed with the draft shield closed. |
| Standard Package | |||
|---|---|---|---|
| Item | Model No. | S124M4-3-0 (Q'ty) |
S124M4-3-1 (Q'ty) |
| S124M4 main body | S124M4-X-A-0001 | 1 | 1 |
| Hard carrying case | HCC-11 | 1 | 1 |
| Battery pack | S947 | 1 | 1 |
| Spare electrode | ELR-01 | 1 pair | 1 pair |
| AC adapter | S979 | 1 | 1 |
| AC power cord | – | 1 | 1 |
| Cooling tray | CTX-03 | 1 | 1 |
| Fiber reformer (4 fiber) | FRF-01 | 1 pair | 1 pair |
| Cleaning brush | VGC-01 | 1 | 1 |
| Electrode sharpener | D5111 | 1 | 1 |
| Tool case | TCC-01 | 1 | 1 |
| LCD antireflectifve sheet | ARS-01 | 1 | 1 |
| Rubber foot | RBC-01 | 1 pair | 1 pair |
| Quick Reference guide | FTS-B559 | 1 | 1 |
| Instruction manual | UMC-03 | 1 | 1 |
| Wi-Fi dongle | WFD-01 | 0 | 1 |
| Optional components | |
|---|---|
| Item | Model No. |
| Soft carrying case | SCC-01 |
| Battery Charger | S980 |
| Angled Stand | AGS-02 |
| Strap plate | SPL-01 |
| Work belt | WBT-01 |
| USB cable | USB-01 |
| Car cigarettes cable | CDC-04 |
| Fiber holder | |
|---|---|
| Item | Model No. |
| Fiber Holder (0.25mm Coating Fiber) | S712S-250 |
| Fiber Holder (0.90mm Coating Fiber) | S712S-900 |
| Fiber Holder (2 Fiber Ribbon) | S712A-002 |
| Fiber Holder (4 Fiber Ribbon) | S712A-004 |
| Fiber Guide V-groove | |
|---|---|
| Fiber count, pitch | Model No. |
| 0.25mm pitch, 4 fiber | FGV-04-P250 |
| Protection Sleeve | ||
|---|---|---|
| Model No. | Applicable Fiber | Length |
| S921 | Single fiber, 0.25 – 0.9mm coating dia. | 60mm |
| S922 | Single fiber, 0.25 – 0.9mm coating dia. | 40mm |
| S924 | Single fiber and up to 8-fiber ribbon | 40mm |
For additional information please contact your sales representative. You can also visit our website at www.lightera.com or call 1-888-FIBERHELP (1-888-342-3743) USA or 1-770-798-5555 outside the USA. For a full list of our certifications, visit our website.
Compare features, sizes, models to find the perfect option for you
